what type of loctite to use for drones
Exercise yous Loctite your Screws on your drone?
02-Feb-2016, eleven:20 PM (This mail service was final modified: 02-February-2016, 11:21 PM by SkinnyShark.)
Hey guys
when building your drone do you have to put loctite on screws or does it matter?
Is it a must have ? I've got some coming haha have to take the motors off and put back on
![[-]](https://intofpv.com/images/collapse.png)
•
02-February-2016, xi:22 PM (This post was terminal modified: 02-Feb-2016, xi:23 PM by fpvmonkey.)
Simply tighten All your nuts, bolts and screws to 48nm and you'll be fine....
I've flown without information technology many times - I include checking everything is correct pre-flying. Nothing has ever failed. My flights only last 5 or 6 minutes. I never employ it during maiden or subsequent examination flights - it encourages me to check and recheck.
Past the fashion, You don't need loctite on nylon nuts, merely on metal to metal connections, like your bolts into the motors.
I dearest to share and assist people! Flying Mini Quad is the best!
•
Loctite on whatever metal parts. Aluminium stand-offs, motors. Unless it's nylon, because plastic is self locking
I also read somewhere you lot tin can just use clear nail smooth, works on plastic besides hehe 
•
I e'er make it a habit to use blue loctite (never red), the amount of vibration and flex running through the frames from the motors/props during flight make it hard for the screws to stay tight all the time. I've learned the hard style a few times of the consequences of things coming off or loose in flight (you'd be amazed at how much the wrong loose screw tin can throw off tuning/setup). Its non a big deal if you don't mind going over every screw before each flight just there are cases when that'southward just non possible, peculiarly if your at an upshot or meetup. As the others have stated just use information technology on metal on metal contact but it volition save you from having to dig and find missing parts or worse when they do come out. Alot of people don't carp with it and I used to exist 1 of them but information technology adds a level of security to ensuring ane less thing can go wrong.
If it isn't broke, prepare it anyways!
•
I loctite all my motor screws, and bottom plate screws to standoffs, every bit I take come up back after some flights missing bottom plate and motor screws. People actually do not think virtually the amount of negative and positive G's the mini quads pull doing acro, which puts a lot of strain on parts. For the small outlay and little time it takes to do I believe it should be loftier on your listing of things to at least consider.
•
I always do. But I didn't know it wasn't needed on nylon - thanks for the tip!
•
I loctite every spiral except the motor ones crusade i'm afraid to get it into the motor
Withal after every crash/repair i check every screw!! I think that information technology more important.
Sky is where the fun begins!
Flying: Armattan F1-6 / Cobra 1960kv / KISS / 1800mAh nano's / SPR3 / Betaflight 2kHz
Building: FPV49v4 modified
•
Annihilation metal on metal in my quad gets threadlocked.
Current quad: ZMR 250 / DYS SE2205 / Littlebee 20A ESCs / Drone Lab 1500 4S / Naze32 Rev5 / BF two.vii.1
FPV: Runcam Skyplus / Aomway 200mw VTX / Fatshark DomV1
>>>>>>>>>>Bank check Out My Build<<<<<<<<<<
•
Definitely do the motor ones! I mean they're extremely important. You only demand a tiny dab on the edge of the motor screw, then screw it in. There is no mode it'll get into the motor.
•
•
I haven't yet only i have lost a few screws white doing test flights etc. So information technology would probably be a good thought for me at least
•
(12-Feb-2016, 01:38 PM)dronehq Wrote: I haven't withal only i have lost a few screws white doing test flights etc. So information technology would probably exist a practiced thought for me at least
I come from heli flying and with a metal frame and a metal head y'all HAVE TO USE loctite or see your head explode mid-flight
And yep, I speak from experience 
BR,
Henrik
•
17-Feb-2016, 12:48 PM (This postal service was last modified: 17-February-2016, 12:49 PM by AndreyM.)
I'm using locknuts for mounting props on my big tricopter. Once I was too lazy to employ thread-locker on them, after 5 minutes of flight the tri fell from the sky and was damaged quite badly. The locknuts on CW-spinning locks came loose and lost thrust :-)
After failing miserably similar that you apace understand the third Newton'south law and other useful theory :-D
•
Source: https://intofpv.com/t-do-you-loctite-your-screws-on-your-drone
0 Response to "what type of loctite to use for drones"
Post a Comment